Description
Introducing The New DV+ T9357
SuitsĀ Various BMW Applications
GFBās DV+ Solution Couldnāt Be Simpler āĀ Keep What Works And Replace What Doesnāt.
Protected by Patents in United States of America, China & Australia
PCT Patents Pending
- Retains the factory solenoid coil for seamless integration
- Replaces plastic valve parts with metal for reliability and strength on chipped engines
- Direct-fit replacement with GFBās TMS benefits
- Exclusive āpilot-actuatedā valve mechanism for rapid response at high boost
GFB expands the DV+ range with a direct-fit solution for the weak factory diverter valve used on many European vehicles.
The solenoid coil itself from the factory-fitted valve is great (the ECU opens it faster than any pneumatic valve so why replace it?), but the weak point however is the valve mechanism itself. So GFBās DV+ solves this problem by replacing just the valve parts with an anodised billet aluminium housing fitted with a brass piston machined to exacting tolerances.
The end result is sharper throttle response, lightning-fast valve actuation, and it will hold as much boost as you can throw at it. Read all about the DV+ story on the next page.
Other manufacturersā products involve replacing the entire system with a traditional pneumatic valve, requiring long vacuum hose runs, additional parts for tapping into the intake manifold vacuum, plus either a different solenoid valve to actuate the pneumatic valve or a ballast resistor to plug into the OE wiring loom. All these additional items result in a product that is slower, less responsive, more expensive and takes much longer to install.
GFBās DV+ solution on the other hand is more responsive, less expensive, easier to install, and doesnāt cause compressor surge/turbo flutter. Oh, and it doesnāt require different springs or frequent re-builds.
The DV+ Story: Better Performance ā More Reliable
Many late-model European cars use ECU controlled solenoid-type diverter valves. This is a good concept because the valve can react very quickly and it only opens when it needs to.
However, there are some problems with these valves. There are typically two types of solenoid-actuated diverter valves found standard on VAG and European cars, both of which have their shortcomings.
Common OE Problem #1 The diaphragm types are commonly known to rupture, especially when boost and temperature are increased as a result of chip tuning. |
Common OE Problem #2 The plastic piston-type leaks far more than most people realise (by design, not from wear), and doesnāt always close after a high-boost gear shift. |
Additionally, in both cases, the solenoid on the OE diverter is directly connected to the valve mechanism, which is not ideal because neither it nor the return spring are strong enough to open and close the valve reliably at high boost.
With problems like this, you can see why other aftermarket manufacturers assume the best solution is to replace the factory diverter entirely. Unfortunately though, whilst their replacement kits might be stronger than the factory diverter, their slower response speed and lower flow do not justify the extra cost and complexity ā more of a compromise than a solution.
GFB has taken a different approach to deliver a complete solution that solves existing problems and improves performance, without compromise or a hefty price tag.
The DV+ addresses the factory valve problems with a very simple and elegant solution. Keeping the factory solenoid retains all the benefits of the stock system, and replacing the valve parts with indestructable metal components ensures strength and reliability no matter how much boost you run.
Thatās not all. Rather than using the solenoid to directly actuate the valve, weāve introduced a unique āpilot-actuationā system. This means the solenoid controls the air pressure that is used to open and close the piston, so it doesnāt matter how much boost you push through it, the DV+ will open and close reliably without ever exceeding the solenoidās capability.
This feature also improves on the factory system by opening the valve progressively in response to boost pressure, so it only opens as much as required to get the job done (the factory valve simply opens and shuts, it cannot partially open if boost pressure is low), resulting in better throttle response.
Unnecessary Replacement Kits AreĀ A Compromise, Not A Solution
Protected by Patents in United States of America, China & Australia
PCT Patents Pending
DV+ Tech TipĀ
PLEASE NOTE: installation of this valve is difficult in some vehicles because of the lack of space and access to the factory diverter location. In some cases the turbo may need to be removed to access the factory diverter to be able to install the DV+.
dv+ Blow off Valve or BOV/ diverter valve with TMS advantage. Protected by Patents in United States of America, China & Australia/ PCT Patents Pending also suits:
- BMW X1 SDrive20i/XDrive20i/XDrive28i E84 (N20 Engine) 2011-15Ā Access To The Factory Diverter Is Extremely Tight. Installation Of The DV+ Usually Requires Loosening Of The Turbo Manifold To Gain Access To The Diverter Valve.
- BMW X1 SDrive20i/XDrive20i/XDrive28i E84 (N20 Engine) 2011-15Ā Access To The Factory Diverter Is Extremely Tight. Installation Of The DV+ Usually Requires Loosening Of The Turbo Manifold To Gain Access To The Diverter Valve.
- BMW 520i/528i F10/F11/F07 (N20 Engine)Ā Access To The Factory Diverter Is Extremely Tight. Installation Of The DV+ Usually Requires Loosening Of The Turbo Manifold To Gain Access To The Diverter Valve.
- BMW Z4 SDrive18i/SDrive20i/SDrive28i E89 (N20 Engine) 2011 - 2016
- BMW X3 SDrive20i/XDrive20i/XDrive28i F25 (N20 Engine)Ā Access To The Factory Diverter Is Extremely Tight. Installation Of The DV+ Usually Requires Loosening Of The Turbo Manifold To Gain Access To The Diverter Valve.
- BMW 320i/328i F30/31/34/35 (N20 Engine)Ā Access To The Factory Diverter Is Extremely Tight. Installation Of The DV+ Usually Requires Loosening Of The Turbo Manifold To Gain Access To The Diverter Valve.
- BMW 220i/228i F22 (N20 Engine) 2014-16Ā Access To The Factory Diverter Is Extremely Tight. Installation Of The DV+ Usually Requires Loosening Of The Turbo Manifold To Gain Access To The Diverter Valve.
- BMW 320i/328i F30/31/34/35 (N20 Engine)Ā Access To The Factory Diverter Is Extremely Tight. Installation Of The DV+ Usually Requires Loosening Of The Turbo Manifold To Gain Access To The Diverter Valve.
- BMW 420i/428i F32/33/36 (N20 Engine) 2013-2016Ā Access To The Factory Diverter Is Extremely Tight. Installation Of The DV+ Usually Requires Loosening Of The Turbo Manifold To Gain Access To The Diverter Valve.
- BMW 420i/428i F32/33/36 (N20 Engine) 2013-2016
- BMW 220i/228i F22 (N20 Engine) 2014-16Ā Access To The Factory Diverter Is Extremely Tight. Installation Of The DV+ Usually Requires Loosening Of The Turbo Manifold To Gain Access To The Diverter Valve.
- BMW X4 Xdrive20i/XDrive28i F26 (N20 Engine)Ā Access To The Factory Diverter Is Extremely Tight. Installation Of The DV+ Usually Requires Loosening Of The Turbo Manifold To Gain Access To The Diverter Valve.
- BMW 220i/228i F22 (N20 Engine) 2014-16
- BMW 320i/328i F30/31/34/35 (N20 Engine)
- BMW 420i/428i F32/33/36 (N20 Engine) 2013-2016Ā Access To The Factory Diverter Is Extremely Tight. Installation Of The DV+ Usually Requires Loosening Of The Turbo Manifold To Gain Access To The Diverter Valve.
- BMW X3 SDrive20i/XDrive20i/XDrive28i F25 (N20 Engine)
- BMW Z4 SDrive18i/SDrive20i/SDrive28i E89 (N20 Engine) 2011 - 2016
- BMW 520i/528i F10/F11/F07 (N20 Engine)Ā Access To The Factory Diverter Is Extremely Tight. Installation Of The DV+ Usually Requires Loosening Of The Turbo Manifold To Gain Access To The Diverter Valve.
- BMW Z4 SDrive18i/SDrive20i/SDrive28i E89 (N20 Engine) 2011 - 2016
- BMW X3 SDrive20i/XDrive20i/XDrive28i F25 (N20 Engine)Ā Access To The Factory Diverter Is Extremely Tight. Installation Of The DV+ Usually Requires Loosening Of The Turbo Manifold To Gain Access To The Diverter Valve.
- BMW M2 F87 (N55B30T0 Engine) 2015-On
DOWNLOAD T9357 INSTRUCTIONS HERE